At times, a person may be on the road for so long that they do not have time to settle and secure a place for their property. This is especially musicians and even show who decide to take their talent on the road. Since it is impossible to travel with the whole house, you will need to own custom road cases. They protect your property and below is how to make them.
Just like any other project, you need to set up your workspace. This includes you gathering all the tools that you will be needing up until the work is done. In order to avoid any form of wasting material, you should have a cut list. The road you intend to build should be in line with the items you want to store in it.
The next step is to cut extruded aluminum. This is one of the elements that result in the road is so strong. The best tool for the job is a cold saw. It does not cause any damage to the aluminum. Measure the length of the uncut side pieces with an uncut piece of u-channel. This is of course measured according to the size of the case you want.
The next step is to make the pockets and notches of the case. These are made out of wood and it should, therefore, be not too difficult to use make them. You will need to mark the cut points and you should, therefore, use the unfinished side of the ABS. Afterward, you should reduce the size of the u-channels to match the sizes of the notches.
For your case to be complete and stand straight, you will need to have corners. This corners not only give the shape but they also ensure that the case has the capacity to hold items inside without fail. These corners do not connect by the use of glue and screws; they actually use rivets to hold them in place. It is recommended to use a pneumatic riveter to put them in place.
You will need to attach the corners to your case. Otherwise, it will just be an undetermined shape. You should hold the corner snug and drill the holes in all the corners then come back around to drill the number of needed holes on each face. These corners are meant to act as absorbers but they at the same time give the case a shape and hide the flaws at the corners.
For the bottom part, you may choose to use a rubber or wheel, whichever you are most comfortable with. As you assemble the road, make sure it is in a closed position. This makes the work easier and allows you the preview of how the road will look after the work is done. Align the corners to ensure that the hinges stay in line.
Finally, you will need to have foam in your case. That foam acts as a shock absorber no wonder it looks so comfortable. While putting it in place, start from the bottom upwards. The foam on the walls, however, should be shorter than the walls to avoid hindering the closing of the case.
Just like any other project, you need to set up your workspace. This includes you gathering all the tools that you will be needing up until the work is done. In order to avoid any form of wasting material, you should have a cut list. The road you intend to build should be in line with the items you want to store in it.
The next step is to cut extruded aluminum. This is one of the elements that result in the road is so strong. The best tool for the job is a cold saw. It does not cause any damage to the aluminum. Measure the length of the uncut side pieces with an uncut piece of u-channel. This is of course measured according to the size of the case you want.
The next step is to make the pockets and notches of the case. These are made out of wood and it should, therefore, be not too difficult to use make them. You will need to mark the cut points and you should, therefore, use the unfinished side of the ABS. Afterward, you should reduce the size of the u-channels to match the sizes of the notches.
For your case to be complete and stand straight, you will need to have corners. This corners not only give the shape but they also ensure that the case has the capacity to hold items inside without fail. These corners do not connect by the use of glue and screws; they actually use rivets to hold them in place. It is recommended to use a pneumatic riveter to put them in place.
You will need to attach the corners to your case. Otherwise, it will just be an undetermined shape. You should hold the corner snug and drill the holes in all the corners then come back around to drill the number of needed holes on each face. These corners are meant to act as absorbers but they at the same time give the case a shape and hide the flaws at the corners.
For the bottom part, you may choose to use a rubber or wheel, whichever you are most comfortable with. As you assemble the road, make sure it is in a closed position. This makes the work easier and allows you the preview of how the road will look after the work is done. Align the corners to ensure that the hinges stay in line.
Finally, you will need to have foam in your case. That foam acts as a shock absorber no wonder it looks so comfortable. While putting it in place, start from the bottom upwards. The foam on the walls, however, should be shorter than the walls to avoid hindering the closing of the case.
About the Author:
You can find a detailed overview of the benefits you get when you order custom road cases at http://www.encorecases.com/products right now.
No comments:
Post a Comment